eye bolt standard pdf

1.1.1 This standard covers only eyebolts with eyes of internal diameters capable of permitting direct engagement with eyehooks of the same lifting capacity ( working load limit ) for use with Grade T( 8 ) chain.

shoulder pattern eye bolts. Machinery Lifting Eye Bolts in this catalog, and other catalogs to which you may refer, could show a higher Working Load Limit (WLL), or Rated Capacity (RC). Lifting Eye Bolts have a safety factor of five times the WLL/RC with proper seating and full thread engagement. 3. The RC of an eye bolt is determined from a

Metric DIN 580 Lifting Eye Bolts Visit our online store for product availability Dimensions of metric DIN 580 lifting eye bolts. All your fastener needs from a single source Aspen Fasteners 4807 Rockside Road, Suite 400, Independence, OH 44131 USA www.aspenfasteners.com | [email protected] | 1-800-479-0056

Note: All Eye Bolts and Eye Nuts, whether in blanks or fully machined, as shown on page B267, are covered by our standard warranty. The warranty becomes VOID whenever modifications are made or further machining is done by the buyer, also in cases where these items are subject to an angular lift or pull. A C E S D M F N T C1035 SPECIFICATIONS IN

1.DIAGRAM 1 It is important to ensure proper alignment of the installed eye bolts before lifting. Referring to DIAGRAM 1: an eye bolt can be turned ¼ turn to ensure proper lifting angles. Never pull across the flats of an eye bolt. 2. TABLE 1 makes reference to the safe working load for shoulder pattern eye bolts.

The dimensions are for your approximate guidance only and manufacturer may not be necessary adhere to above specifications. Other threads can also be supplied 

The above eye bolts comply to British Standards as follows: Short Shank code WIR15112 to BS 4278 Part 1 1984. [The scope of this standard starts at M12 - the M10 is machined from an M12 forging].

Each eye bolt and eye nut is individually stamped with:. The ASME B30.26 standard is applicable only to carbon steel eye bolts specifies that carbon steel eye bolts are only to be used above -1°C. For environments below -1°C the standard is ASTM F541-12.

Crosby® S-279 Machinery Eye Bolt UNC M-279 Crosby® S-279 Machinery Eye Bolt Metric Shoulder Type Eye Bolts Shoulder Type Eye Bolts *Ultimate Load is 5 times the Working Load Limit. Maximum Proof Load is 2 times the Working Load Limit. **On Request: Special threading or as forged bolts for customer conversion. •Forged Steel - Quenched

Crosby® 275 Forged Screw Eye Bolts Crosby® 275 Forged Screw Eye Bolts > Eye Nuts. Crosby® 400 Eye Nuts Crosby® 400 Eye Nuts > Lifting Eyes. Crosby® 405 Lifting Eyes Crosby® 405 Lifting Eyes > Pad Eyes. Crosby® 264 Pad Eyes Crosby® 264 Pad Eyes > Standard Hoist Rings. Cold Temperature.

DIN 580 Specification specifies the properties of steel and stainless steel eyebolts and provides information on their correct use in lifting operations (as part of slings and as load handling equipment). Eye bolts according to this standard can be used in a temperature range from −20 ° C to +200 ° C without any restriction of the load capacity.

Learn more about our eye bolts including eye bolt capacity and eye bolt sizes. are manufactured to ASME B18.15 and tested to ASTM A489 specifications 

DIN 580 Specification. Lifting Eye Bolts. DIN 580 Scope. DIN 580 Specification specifies the properties of steel and stainless steel eyebolts and provides information on their correct use in

USE ONLY SAFEPOINT & SWIVEL EYE BOLT FOR ANGLE LIFTING. SafePoint Forged Eye Bolt Specifications given are indicative and are subject to change.

The above eye bolts comply to British Standards as follows: Short Shank code WIR15112 to BS 4278 Part 1 1984. [The scope of this standard starts at M12 – the M10 is machined from an M12 forging].

Lifting eye bolts. BN 257. +2. DIN 580. ~ISO 3266. ~UNI 2947. ~ČSN 021369 Order now. Product data sheet (PDF). Product variants (23) 

Product Dimensions, Standards and Weights. DIN 444 Technical Specifications. Metric DIN 444 Eye Bolts. Visit our online store for product availability.

See Safe Lifting Chart on page 5. All rated capacities consider a straight vertical lift. Use CAUTION when lifting. Any angle beyond vertical (zero degree) will 

plain & shoulder eye bolts shoulder eye bolts the actual load a single eye bolt can lift is referred to as "riggers load." engineers capacity is the allowable tension in the eye of the lifting rig as it is applied to the eye bolt. it is necessary to determine the tension in each rig leg before sizing the eye bolt. shoulder eye bolts united part no.

Designation of a lifting eye bolt with thread d₁ -M 20:₁ Lifting eye bolts according to the present Standard shall be manufactured solely from C 15.

to the standard: DIN 580 for eye bolts or DIN 582 for eye nuts; • when used as a lifting device, the eye bolt or eye nut should always be fully screwed into the load in such a way that it fits properly against the load; • make sure the thread is undamaged and clean; • eye bolts and eye nuts are free from nicks, gouges and cracks;

Dimensions of Metric Machinery Eye Bolts with Shoulder. Print this page. Size. (A x Pitch x B) Outside Eye Diameter. (C) (mm) Inside Eye Diameter. (D)

Eye Bolt under 12mm is not suggested to use for lifting purposes ,refer to relevant standards. 8. Eye Bolts should always be used in accordance with 

The threading is standard metric. Eye bolts and eye nuts are drop forged from C15 steel. Each eye bolt and eye nut is generally marked with:.

Hex key cover plate. Zinc plated steel. GN 581 swivel lifting eye bolts offer a high load carrying capacity and are tested to meet high safety standards. The 

Standard Eye Bolts, Rod Ends On Morton Machine Works All Categories > Bolts > Standard Eye Bolts, Rod Ends > View Items Standard Eye Bolts, Rod Ends Email This Page Download PDF Printable Page Available in carbon steel, black oxide finish or stainless steel Precision machined from bar stock Eye bolts are not recommended for lifting applications

6 Proudy Servig Distriutors Sice 1899 LIFTING EYE BOLTS LIFTING EYE BOLTS C E ØD B A Design: Shoulder Pattern Process: Forged Threads: UNC Material: 1045 Carbon Steel Finish:

Eye Bolt Rating and Specifications - Free download as PDF File (.pdf), Text File (.txt) or read online for free.

0.3 This specification covers eyebolts designed to use with shackles. The provision of a collar adds substantially to the strength of an eyebolt and eye- bolts 

Free download standard DIN 580 DIN 582 and another documents. Here are 4 golden rules to buy STAINLESS STEEL lifting Eye Bolts and Lifting Eye Nuts 

4655 12 point bolt flange shoulder bolt u bolt eye bolt us 10 50 12 00 pieces m8 m72 hastelloy x alloy steel bolt price per piece us 0 20 2 00 piece uns n06002 hastelloy x 2 4655 hastelloy x big nut heavy hex nut, hastelloy c276. This Standard has been prepared in four parts as follows; Part 1: Hooks . Part 2: Shackles . Part 3: Eye bolts.Part 4: Chains . Each part can be used independent